MS-930 Silicon Modified sealant
MS-930 Silicon Modified sealant
INTSHAYELELO
I-MS-930 yintsebenzo ephezulu, engathathi hlangothi ye-single-component sealant esekwe kwi-MS polymer.Iphendula ngamanzi ukwenza i-elastic material, kunye nexesha layo lokukhulula kunye nexesha lokunyanga lihambelana nobushushu kunye nomswakama.Ukunyusa ubushushu kunye nokufuma kunokunciphisa i ixesha lokukhulula kunye nexesha lokunyanga, ngelixa ubushushu obuphantsi kunye nokufuma okuphantsi kunokulibazisa le nkqubo.
I-MS-930 inomsebenzi obanzi we-elastic seal kunye nokubambelela.Ifanelekile kwiindawo ezidinga ukutywinwa kwe-elastic ukongeza kunye namandla athile okunamathela.
I-MS-930 ayinavumba, i-solvent-free, i-isocyanate ikhululekile kwaye i-PVC ikhululekile .Inokubambelela kakuhle kwizinto ezininzi kwaye ayifuni i-primer, ekwafanelekile kwi-spray-painted surface.Le mveliso ibonakaliswe ukuba inokumelana ne-UV ebalaseleyo. , ngoko inokusetyenziswa ngaphakathi nangaphandle.
IIMBONAKALO
A) Akukho formaldehyde, akukho isinyibilikisi, akukho ivumba ekhethekileyo
B) Akukho ioli ye-silicone, akukho konakala kwaye akukho ngcoliseko kwi-substrate, i-imeko-friendly
C) Ukubambelela kakuhle kwezinto ezahlukeneyo ngaphandle kwe-primer
D) Ipropathi efanelekileyo yoomatshini
E) Umbala ozinzileyo, ukuchasana okuhle kwe-UV
F) Icandelo elinye, kulula ukulakha
G) Inokupeyintwa
ISICELO
Imveliso yemizi-mveliso, efana nokudityaniswa kweemoto, ukwenziwa kweenqanawa, ukwenziwa komzimba kaloliwe, ukwakhiwa kwecontainer yentsimbi.
I-Ms-930 inokubambelela kakuhle kwizinto ezininzi: ezifana ne-aluminium (ipolishiwe, i-anodized), ubhedu, intsimbi, insimbi engenasici, iglasi, i-ABS, i-PVC enzima kunye nezixhobo ezininzi ze-thermoplastic.I-ejenti yokukhululwa kwefilimu kwiplastiki kufuneka isuswe ngaphambi kokubambelela.
Inqaku elibalulekileyo: I-PE, PP, PTFE ayinamathele kwi-relay, izinto ezikhankanywe ngasentla azikhuthazwa ukuba zivavanye kuqala.
Umphezulu we substrate wangaphambi konyango kufuneka ucoceke, wome kwaye ungagayi amafutha.
INDLELA YOBUGCISA
| Umbala | Mhlophe/Mnyama/eNgwevu |
| Ivumba | N / A |
| Ubume | Thixotropy |
| Ukuxinana | 1.49g/cm3 |
| Umxholo oqinileyo | 100% |
| Indlela yokunyanga | Ukunyanga ukufuma |
| Umphezulu ixesha elomileyo | ≤ 30min* |
| Izinga lokunyanga | 4mm/24h* |
| Tensile strength | ≥3.0 MPa |
| Ukwandisa | ≥ 150% |
| Ubushushu bokusebenza | -40℃ ukuya kwi-100℃ |
* Iimeko ezisemgangathweni: iqondo lobushushu 23 + 2 ℃, ukufuma okunxulumene 50±5%
INDLELA YOKUFAKA ISICELO
I-manual ehambelanayo okanye i-pneumatic glue gun kufuneka isetyenziswe ukupakisha okuthambileyo, kwaye kuyacetyiswa ukuba ulawule ngaphakathi kwe-0.2-0.4mpa xa kusetyenziswa i-pneumatic glue gun.Ukushisa okuphantsi kakhulu kuya kukhokelela ekunyuseni kwe-viscosity, kucetyiswa ukuba kufakwe i-preheat sealants kwiqondo lokushisa ngaphambi kokusetyenziswa.
UKUSEBENZA KWAMANDLA
I-Ms-930 inokupeyintwa, nangona kunjalo, iimvavanyo zokuziqhelanisa ziyacetyiswa kwiintlobo ezininzi zepeyinti.
UKUGCINA
Ubushushu bokugcina: 5 ℃ ukuya kuma-30 ℃
Ixesha lokugcinwa: Iinyanga ezili-9 kwipakethe yokuqala.
